ANCEL DS600 Professional TPMS Programming Key Coding Auto Diagnostic Tool

ANCEL DS600 Professional Scanner= Full System Car Diagnostic Tablet Wifi Bluetooth + 28 Special Functions ECU Coding Bi-directional + 2 Year Free Update Online + Android 10.0 + 8" Touch Screen + Multi Languages Supported + 2GB RAM+32G

Full System Diagnostic Scanner

• To diagnose Brake System: if you feel the brake pedal is mushy and notice unusual odor or noise, etc. A properly operating brake system is critical to ensure safe vehicle control and operation;

• To diagnose Emission System: if the system is affected by vehicle age or poor quality fuel. A good emission system reduces harmful gases to a large degree and protects you from being fined;

• To diagnose Fuel system: if vehicle won't start or "Check Engine" light is illuminated. Check car's fuel system regularly ensures the best performance of your car with the lowest emissions;

• To diagnose Transmission System: if your car is slipping or difficult to shift. The system plays an important part in the overall performance of your car;

• To diagnose Wiper System: if you observe chattering or streaking wiper. If the car is not regularly checked, the accident might happen because you can't see clearly;

• To diagnose Light System: if you see rapid signal blinking or dimming lights.

• And many more ...

 Support 28+ Special Functions

1. Oil Reset

The lightening of the car maintenance light indicates that the vehicle needs maintenance. Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle.

2. DPF Regeneration

DPF Regeneration is used to clear PM(Particulate Matter)from the DPF filter through continuous combustion oxidation mode (such us high-temperature heating conbustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter perfornance.

DPF regeneration may be performed in the following cases:

1. The exhaust back pressure sensor is replaced

2. The PM trap is removed or replaced

3. The fuel additive nozzle is removed or replaced

4. The cataytic oxidizer is removed or replaced

5. The DPF regeneration MIL is on and maintenance is performed

6. The DPF regeneration control module is replaced

3. AFS (headlamp) Reset

The feature is used to initialize the adaptive headlamp system. According to the ambient light intensity, the adaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjust the headlamp lighting angle while monitoring the vehicle speed and body posture.

4. EGR Adaption

This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.

5. Brake-pad Reset

If the brake pad wears the brake pad sense line,the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad. Otherwise, the car alarms.

Reset must be performed in the following cases:

1. The brake pad and brake pad wear sensor are replaced.

2. The brake pad indicator lamp is on.

3. The brake pad sensor circuit is short, which is recovered.

4. The servo motor is replaced.

6. IMMO Service

To prevent the car from being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. When the ignition switch key, ignition switch, combined instrument panel, ECU, BCM, or remote control battery is replaced, anti-theft key matching must be performed.

7. Windows Calibration

This feature is designed to perform door window matching to recover ECU initial memory and recover the automatic ascending and descending function of the power window.

8. Coolant Bleeding

Use this function to activate the electronic water pump before venting the cooling system.

9. Steering Angle Reset

To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. After replacing the steering angle position sensor, replacing steering mechanical parts (such as steering gearbox,steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering car body, you must reset the steering angle.

10. Injector Coding

Writing injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced, injector code of each cylinder must be confirmed or re-coded so that cylinder can better identify injectors to accurately control fuel injection.

11. Seat Calibration

This function is applied to match the seats with memory function that are replaced and repaired.

12. Transport Mode

In order to reduce power consumption,the following functions may be disabled,including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, etc. At this time, the transport mode needs to be deactivated to restore the vehicle to normal.

13. Battery Matching

This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.

Battery matching must be performed in the following cases:

1. Main battery is replaced. Battery matching must be performed to clear original low battery information and prevent the related control module from detecting false information. If the related control module detects false information, it will invalidate some electric auxiliary functions, such as automatic start&stop function, sunroof without one-key trigger function, power window without automatic function.

2. b)Battery monitoring sensor. Battery matching is performed to re-match the control module and motoring sensor to detect battery  power usage more accurately, which can avoid an error message displaying on the instrument panel.

14. Airbag Reset

This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collides and the airbag deploys, the corresponding fault code of the colision data appears, the airbag indicator lights up,and the fault code can't be cleared. Since the data inside the airbag computer is disposable, it is required that all new accessories must be ewplaced, but after performing this function, the data of the airbag computer can be recovered and the fault code can be cleared, the airbag light will go out,and the airbag computer can continue to use.

15. Tyre Reset

This function is used to set the size parameters of the modified or replaced tire.

16. ODO Reset

ODO reset is to copy, write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual mileage.

Usually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure, it is necessary to do ODO reset after maintenance.

17. ABS Bleeding

When the ABS contain air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity. If the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake line, or brake fluid is replaced, the ABS bleeding function must be performed.

18. Gear Learning

The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computer to more accurately diagnose engine misfires. lf gear learning is not performed for a car equipped with Delphi engine, the MlL turns on after the engine is started. The diagnostic device detects the DTC P1336' gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car. After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, or crank shaft flywheel is replaced, or the DTC' gear not learned" is present, gear learning must be performed.

19. Language Change

This function is used to change the system language of the vehicle central control panel.

20. Adblue Reset

After the diesel exhaust treatment fluid (car urea) is replaced or filled up,urea reset operation is required.

21. Elec. Throttle Adaption

Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state. By doing these, the movement of the throttle (or idle motor) can be more accurately controlled, thus adjust the intake volume.

22. Suspension Matching

This function can adjust the height of the body. When replacing the body height sensor in the air suspension system, or control module or when the vehicle level is incorrect, you need to perform this function to adjust the body height sensor for level calibration.

23. A/F Reset

This function is applied to set or learn Air/Fuel ratio parameters.

24. Nox Sensor Reset

Nox sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. If the NOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine ECU.

25. TPMS Reset

After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting function must be performed to reset tire pressure and turn off the tire pressure MIL. Tire pressure resetting must be performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tire pressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged, and tire is replaced for the car with tire pressure monitoring function.

26. AT Learning

This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox is disassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impact problem. In this case, this function needs to be done so that the gearbox can automatically compensate according to the driving conditions so as to achieve more comfortable and better shift quality.

27. Sunroof Initialization

This function can set the sunroof lock off, closed when it rains, sliding/tilting sunroof memory function, temperature threshold outside the car etc.

28. Stop/Start Reset

This function is used to open or close the automatic start-stop function via setting the hidden function in ECU (provided that the vehicle has a hidden function and supported by hardware).

ECU Coding and Active Test (Bi-directional)

This diagnostic tablet supports ECU coding function on a large amount of makes, including for Benz, for Ford and more. It also supports quick diagnosis via one-button VIN scanning.

Active test (Bi-directional) is used to test whether the execution components in the electronic control system can work normally.

Remote Technical Support

By using this function, users can receive ad-hoc remote support from ANCEL's technical engineers, colleagues, or friends, by allowing them to control this tablet device on their PC via the TeamViewer software.

Support Car List

Supports 10000+ car models from America, Europe, Asia (Including Russian car models, Chinese car models, Indian car models, Malaysian car models, Australian car models, Brazilian models, Latin American models, and other national car models)

American: Compatible for DODGE, FIAT(BRAZIL), FORD, FORD(AUSTRALIA), JEEP, LINCOLN

European: Compatible for ABARTH, ALFA ROMEO, ASTON MARTIN, AUDI, BENTLEY, BMW, BUGATTI, CITROEN, DACIA, DR, FORD(EUROPE), FERRARI, FIAT, GAZ, OPEL(SOUTH AFRICA), IVECO, IZH, JAGUAR, LAMBORGHINI, LANCIA, LAND ROVER, MASERATI, MAYBACH, MERCEDES-BENZ, MINI, OPEL, PAZ, PEUGEOT, PORSCHE, RENAULT, ROLLS ROYCE, ROVER, SAAB, SEAT, SEAT, SKODA, SMART, SPRINTER, UAZ, VAUXHALL, VAZ, VOLVO, VW, ZAZ

Asian: Compatible for ACURA, DAEWOO, DAIHATSU, HOLDEN(AUSTRILIA), HONDA, HYUNDAI, IKCO, INFINITI, ISUZU, KIA, LEXUS, LUXGEN, MAHINDRA, MAHINDRA(INDIA), MARUTI, MARUTI(INDIA), MAZDA, MITSUBISHI, MVM, NISSAN, GTR(NISSAN), PERODUA, PERODUA(MALAYSIA), PROTON, PROTON(MALAYSIA), SAMSUNG, RENAULT SAMSUNG, SAIPA, SSANGYONG, SUBARU, SUZUKI, TATA, TATA(INDIA), ISUZU(THAILAND), TOYOTA, UNITED PAKISTAN

Chinese: Compatible for SENORA(BAIC), WEIWANG(BAIC), BJEV, BAIC, BRILLIANCE, BYD, CHANGAN, CHANGE, CHANCE SUZUKI, DFCITROEN, ECUAID, FAW(TIANJIN), FOTON, GEELY, jinlong, GONOW, GWM, HAFEI, HAIMA, JAC, JAC REFINE, SHIERAY, JMC, JOY LONG, LIFAN, MG(SAIC), QOROS, MAXUS, SGM, SOUTHEAST, SPARK, SGMW, DFSK, XINKAI, POLAR SUN, ZX AUTO, ZOTYE

Key Analysis

2. Power Key

Press and hold it for 3 seconds to turn it off

Press and hold it for 8 seconds to perform forced shutdown

Press it once to activate or turn off the device

3. Type C Charging Slot: connect the suppiled charger for charging

4. USB Port: Reserved for add-on modules and other device with similar port

5. Rear Camera

6. Speaker

7. Backplane: remove the backplane of the tablet,and install function modules on the backend

8. PIN: Used for communication between the function expansion module and the host

9. Adjustable Kickstand: Flip out it to 180-degree angle and work comfortable at your desk,or hang it on automotive part

10. Rubber Protection Sheet

Support Multi-languages

Italian, English, German, Japanese, Russian, French, Spanish, Portuguese, Polish, Turkish, Dutch, Greek, Hungarian, Arabic, Danish, Korean, Persian, Romania, Serbia, Finnish, Swedish, Czech, Chinese (traditional)

Product Parameters

• Operating System: Android 10
• Camera: Rear camera 8.0MP
• Memory: 4G
• Network: Wi-Fi, WL AN 802. 11b/g/n
• Storage: 64G
• Bluetooth: Bluetooth 5.0
• Battery: 6000mAh/7.6V
• Working Temperature: 0°C ~ 50°C
• Screen: 10 inches
• Storage Temperature: -20°C ~ 60°C

Package List

• 1 x Password Paper
• 1 x Instruction
• 4 x 5JF5AL250V Fuse
• 2 x 5A250V Fuse
• 1 x EU Plug
• 1 x CN Plug
• 1 x For BMW-20
• 1 x Three-Seater Plug
• 1 x VCI Bluetooth Adapter
• 1 x G/V+12
• 1 x TA-22
• 1 x CR-6
• 1 x HA-3
• 1 x TA-17
• 1 x USB-Micro
• 1 x For Fiat-3
• 1 x USB-type C
• 1 x M/H-12+16
• 1 x for Benz-38
• 1 x power cable clips
• 1 x OBD2 16 pin main cable
• 1 x Xigeartt Lighter Cable
• 1 x OBD1 Adaptor
• 1 x NN-14+16
• 1 x Main Tablet
• 1 x Plastic box
• 1 x Carton